![]() ![]() Your monitor should have an "Auto" button on it somewhere that is used to calibrate and center the display - press the button and watch the magic happen before your eyes. Use the Auto Button to Calibrate your Display Automaticallyįortunately, the fix for this is very simple. This caused the entire screen to shift because the monitor wasn't configured for 59Hz in its hardware settings. Screen wrap messed up driver#I had the exact same problem with one of my PC's that I upgraded to Windows 10 after the upgrade, the display driver was using 59Hz instead of the regular 60Hz, which I had previously set. The reason your display is shifted is most likely because Windows 10 installed a new display driver, or changed the display frequency settings to something other than what you had set in your previous operating system. Screen wrap messed up upgrade#Any ideas what is going on? Should I upgrade my video driver or do I need to whack my monitor? Thanks in advance for any advice you can give me, and many, many thanks for all you have taught me over the years. In fact, the clock appears to be missing the 'AM' or 'PM', and the date shows only the month and day, but not the year. The left side of the screen has a small black border around it. You want to highlight line 3 (V) in order to replace it, but when you do, the highlighted text is that of another line.I just installed Windows 10 over this past weekend, but my LCD monitor's display seems to be shifted to the right, and the fonts are fuzzy. And don't even think about using VIM in such a misaligned terminal. ![]() It's pretty much anything that uses a pager - the first few lines are often missing (for example). It's actually rather difficult not to run into this frequently.Īnd the result isn't just that some man pages aren't showing up properly. Admins usually log in from different computers and when the attached monitors differ in size (resolution), a window that's maximized will have a different size on each computer. You don't have to resize your terminal windows to run into this. If you use Terminator, you can skip the first three steps because it shows the number of columns and rows at the top. Type in stty rows N and stty columns N where N is the "real" number (outside of screen).Įxample: $ stty rows 33 stty columns 133.The stty output should be different.Įxample: speed 38400 baud rows 47 columns 177 line = 0 Go back to your remote tab or log in and reattach screen.stty -a | grep rows: Get the number of rows and columns.Įxample: speed 38400 baud rows 33 columns 133 line = 0.Or: Leave screen (Ctrl + A D to detach) and log out of your SSH session. Ctrl + T: Open a new tab with a local shell.If other measures like Ctrl + A Ctrl + L don't work, try using stty: Well, that's a common problem and there should be a simple solution. I think it was size 80 x 25 and then after a while, I resized the Terminal to 130 x 50 approximately, and then the "inner shell" (of the VM) started to behave weird). ![]() Update: I remember now how it happened in Fedora: I opened up a Terminal, and did a FreeVM to use a console of a Virtual Machine (a shell). (this happened before right inside Fedora, and also for a Macbook ssh into a RHEL 5.4 box). So if we don't close the shell, is there a way to fix this problem? One way that works is to log out or close the window, and resize the window first, and then do ssh (or close that tab, and resize the window, and then open a new tab to get a new shell).īut this way, we will lose anything that we previously did, such as starting a virtual machine console, etc. The command reset is tried and it wouldn't work. (for example, treat the end of screen as some where in the middle of the screen). Sometimes, a terminal screen is messed up, and when we use man ls to read the manpages, or press the UP arrow to go to previous commands in history, the screen will show characters not as the right place. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |